PC-Auto Bond™ is a fast curing, strong and flexible cold weld Epoxy formulation. Product can be applied using a mixing nozzle or mixing stick. PC-Auto Bond™ is an extremely flexible epoxy with exceptional tensile adhesion and peel strength to a wide variety of substrates. In just a few minutes PC-Auto Bond™ forms a tough bond without the need for clamping. Product exhibits superior shatter, impact or vibration stability and resistance.
Added flexibility creates high strength, permanent bond.
Here are just a few specific uses (there are hundreds of other uses):
- Attach weather stripping to garage door.
- Secure house numbers to brick.
- Fix mailbox door.
- Fix plastic printer cover.
- Reattach molding or trim on a vehicle.
- Attach foam rubber door seal.
- Use static mix nozzle to seal wires thru holes in machine walls.
- Attach metal plaques to stainless steel.
- Seal cracks in plate metal.
PC-Autobond™ | 1 oz.
How to prepare a surface for bonding with PC-AutoBond™ Epoxy
Remove contaminants such as dust, dirt, oil and grime with a solvents such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use mineral spirits or paint thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion.
How to clean-up after PC-AutoBond™ Epoxy application
Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover.
Can PC-AutoBond™ Epoxy be used to repair a canvas awning?
PC-AutoBond™ Epoxy is excellent for repairing fabrics. Within 30 minutes PC-AutoBond™ Epoxy reaches functional strength.
What substrates does PC-AutoBond™ Epoxy stick to?
PC-AutoBond™ Epoxy sticks exceptionally well to rubber trim or insulation and various plastics such as PVC, polycarbonate, acrylic, ABS, metals, wood, ceramics and concrete.
What size packages is PC-AutoBond™ Epoxy available?
PC-AutoBond™ Epoxy is packaged in a 25 ml ( 1 oz.) dual syringe with a mixing nozzle and mixing stick.
Does PC-AutoBond™ Epoxy require additional equipment such as an applicator/gun, mix board or putty knife?
No, the viscosity of PC-AutoBond™ Epoxy is such that it can be manually dispensed via the supplied static mixing nozzle directly to the repair.
Does PC-AutoBond™ Epoxy cure fast?
Yes, expect PC-AutoBond™ Epoxy’s work-life to be over in 10 minutes and functionally cured within 30 minutes.
Can PC-AutoBond™ Epoxy be mixed on a flat surface or in a container?
Although PC-AutoBond™ Epoxy is supplied with a mix nozzles it can also be mixed with a putty knife in container or on mix board.
Is PC-AutoBond™ Epoxy a paste?
It is a dark gray non-drip paste formula.
Is PC-AutoBond™ Epoxy flexible?
PC-AutoBond™ Epoxy is flexible. It is not at all brittle.
Is PC-AutoBond™ Epoxy suitable for cold temperatures?
Yes, PC-AutoBond™ Epoxy cures down to 35°F (2°C)
The product in the mixer is cured
Dispose and mix with putty knife or mixing stick.
Does not stick to Polyethylene or Polypropylene toys
Many toys are constructed of Polyethylene or Polypropylene plastic. These types of plastic cannot be repaired with epoxies.
The cap is lost, how should the remainder PC-AutoBond™ Epoxy be stored?
You can leave the spent static mix nozzle on the syringe until you are ready to use again or wrap with aluminum foil.